Discovering Plumbing Basics is Vital for Bathtub Installation
Discovering Plumbing Basics is Vital for Bathtub Installation
Blog Article
Here below you can find a lot of dependable points around How to Install a Bathtub.
Mounting a bathtub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately hard project. If the old tub is easily easily accessible, the job can move immediately; if you need to open a wall surface to remove the old bathtub as well as place the new tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have qualified on your own for the work as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is better to think about employing one before you start. Chances are you may need a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new tub in your restroom if you have actually already bought a new bathtub as well as don't need to transform the arrangement of your previous water system pipelines.
Your devices as well as product list ought to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning throughout this process. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former kind should be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bathtub
Making use of both wood boards under its feet, put the bath tub in the needed position. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water as well as examine all joints and brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as likewise examine the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the tub ought to wait up until the bath tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be suited its final setting.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall in between the bath as well as the tiling, resulting in issues with dampness and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently readily available on the market. It is suggested to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that piece of content was a great idea. Liked our article? Please share it. Let someone else find it. Thank-you for taking the time to read it.
Choose excellence in emergency plumbing. Report this page